Cable Tracers & Cable Testers

Receiver
● The 5500 CB receiver is designed to identify and trace wires or cables.
● Designed for locating unenergized cables and powered cables.
● Signal Detection (includes Level, Code, Value)
• Automatic Mode
• Manual Mode (There are 9 levels to select).
● UAC Mode (AC Power Line Detection)
● Flashlight & Back Light function.
● The Silent Mode (Disable Button Beep & Frequency Tone)
● The Danger Symbol is to indicate the AC voltage on the Line.
● The Level Bar Display on the LCD Screen for the
signal value & the UAC power value.
● Auto power off function.

● Four transmitter plug types
– RJ-11          –  RJ-45
– COAX        –  Alligator clips
● Two unique audible tones:
– Fast alternating tone
– Slow alternating tone   
● Telephone line polarity check
    – Tip side
– Ring side
● Cable tracing
● Telephone line status check
– Clear line
– Busy line
– Ringing line
● Continuity check.
● Transmitter plug storage.
● Easy to store different kinds of transmitter
plugs (RJ-11, RJ-45, COAX, and alligator clips).
● Easy to carry.
● Flashlight function.

Amplifier Probe

● The Amplifier Probe is designed to identify
and trace wires or cables within a group
without damaging the insulation.
● Works with any Tone Generator to identify wires.
● Volume control for increased sensitivity and
adjustable to suit work environment.
● Recessed ON/OFF button prevents battery drain.
● A phone jack is designed for headset or handset.        

Non-contact Voltage Detector

● Non-contact voltage detection :
50V ~ 1000V AC
● Frequency : 50 ~ 500 Hz
● Measurement category : CAT IV 1000V.
● Indication : LED and Tone
● Bright LED and audible alarm sound  when voltage is present.
● Designed for Non-contact voltage  detection. It’s safer.
● Can be used to find a break in a wire.
● Flashlight function.
● NCV Test button design.
● Operating Conditions :
Temperature : 0 ~ 40°C
Humidity : Less than 80% R.H.
Altitude : 2000 m (6500 feet) maximum
● For indoor use only.
● Pollution degree : 2. 

● 165 CB is an ideal tool which can test the correct pin configuration
for different kinds of cables.
● For testing:
-RJ45/RJ11         -USB
-COAX               -BNC cable
-Multi-wire cable
● Auto-scan and manual-check function
● Buzzer sound warning for wire status
● 2 LED module indicators on the master unit which can
do both of transmitter and receiver functions for
RJ45/RJ11 cable testing. Users don’t need to use the receiving unit.
● 165 CB provides a variety for checking cable continuity,
open status, short status and miss-wired.
● Ground (shielded ) wire test.
● LED indication for wire status.
● Power source : 9V battery

Amplifier Probe

● The Amplifier Probe is designed to identify and trace
wires or cables within a group without damaging the insulation.
● The flashlight function for easier cable tracing in the dark.
● An LED indication for the signal strength.
● Volume control for increased sensitivity and adjustable
to suit work environment.
● Recessed ON/OFF button prevents battery drain.
● Works with any Tone Generator to identify wires.
● Power supply is in any 9V battery with a life of approximately 100  hours.
● A phone jack is designed for headset or handset.

Tone Generator

● Tone Generator is a great tool for locating and
identifying cable pairs or individual conductors.
● Two bi-colored LEDs for Line1 and Line2 indication of
the polarities of the telephone lines.
● Identifying Tip and Ring of telephone lines
● Identifying telephone line condition : Clear line, Busy
line and Ringing line.
● 165 CB does not only serve as a tone generator, but
it also serves as a continuity and polarity tester.
● Users can select a fast dual tone or a slow dual tone
by the rotary switch.
● The unit has alligator type terminals, a modular cable
of 4 conductors with a strong connector.
● The tone and continuity functions are only applied to
Line1. (modular connector)

● The Amplifier Probe is designed to identify and trace
wires or cables within a group without damaging
the insulation.
● Works with any Tone Generator to identify wires.
● Volume control for increased sensitivity and adjustable
to suit work environment.
● Recessed ON/OFF button prevents battery drain.
● A phone jack is designed for headset or handset.

Tone Generator

● Tone Generator is a great tool for locating and
identifying cable pairs or individual conductors.
● 181 CB-G does not only serve as a tone generator,
but also serves as a continuity and polarity tester.
● A tone selector switch located inside the unit for
selection of the fast tone or the slow tone.
● The continuity function is only applied to Line 1.
● Two bi-colored LEDs for Line1 and Line2 indication
of the polarities of the telephone lines.
● The unit has alligator type terminals, a modular cable
of 4 conductors with a strong connector.

● The Amplifier Probe is designed to identify and trace
wires or cables within a group without damaging
the insulation.
● Works with any Tone Generator to identify wires.
● Volume control for increased sensitivity and adjustable
to suit work environment.
● Recessed ON/OFF button prevents battery drain.
● A phone jack is designed for headset or handset.

Tone Generator

● Tone Generator is a great tool for locating and
identifying cable pairs or individual conductors.
● 180 CB-G doesn’t only provide the function of a tone
generator, but also serves as a continuity and polarity
tester.
● Test results are displayed by a bi-colored LED.

● The Amplifier Probe is designed to identify and trace
wires or cables within a group without damaging
the insulation.
● Works with any Tone Generator to identify wires.
● Volume control for increased sensitivity and adjustable
to suit work environment.
● Recessed ON/OFF button prevents battery drain.
● A phone jack is designed for headset or handset.

Tone Generator

● Tone Generator is a great tool for locating and
identifying cable pairs or individual conductors.
● 181 CB-G does not only serve as a tone generator,
but also serves as a continuity and polarity tester.
● A tone selector switch located inside the unit for
selection of the fast tone or the slow tone.
● The continuity function is only applied to Line 1.
● Two bi-colored LEDs for Line1 and Line2 indication
of the polarities of the telephone lines.
● The unit has alligator type terminals, a modular cable
of 4 conductors with a strong connector.

● Trace wires or cables.
● Volume control.
● Tip & Ring identification.
● 2 bi-colored LEDs ( Line 1 & Line 2).
● Tone speed selection : Fast & Slow.
● A phone jack is designed for headset or handset.
(Amplifier probe)

Digital Multimeter

● 4000 counts.
● ACV, DCV.
● Ohm, Diode, & Continuity testing.
● Auto-range.
● Data hold.
● Low battery indication.
● Select function.
● Auto-off.

● Designed for RJ45/RJ11 modular cables, 10/100
base-T cable and Token Ring cable etc.
● The LAN cable tester can verify cable continuity,
open, circuit and miss-wired.
● The remote receiving unit is available for installed
cables far away either on the wall plates or on the
patch panels.
● Auto and manual scan function.
● Ground wire test.
● Display : LED indication for wire status.

Digital Multimeter

● 4000 counts LCD.
● Full automatic measurement.
Voltage measurement.
Resistor measurement.
● Range change function.
● Select function.
● Data Hold function.
● Continuity check.
● Diode measurement.
● Low battery indication.
● Input impedance:10MΩ.