Download (software, documentation)

Software for device programmers

Elnec provides one common software for all device programmers. There are available regular version and OnDemandversions of software. Regular version is released normally every 3-4 weeks, OnDemand versions are released on demand – for hot new devices support and bugs fixes – often daily. For detailed description of control program for programmers look please at Software page.

Elnec software is in the form of installer, which copies control software for Elnec programmers to your hard disk, creates shortcuts in the start menu and associates project files with Elnec software, if desired.

The setup program must run with administrative rights, however Elnec software runs fine without administrative rights once it is installed.

Installation: To install Elnec software for programmers, run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file and follow the wizard.

Updating: Run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file. You do not need to uninstall the old version first. Your configuration options will not be lost.

Silent Installation: The PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) installer supports command line switches for silent installation, i.e. the program gets installed without asking the user for target directory or association options. The default settings of the installer are used. The /SILENT command line switch performs a silent installation and shows a status dialog during the setup process. No questions will be asked though.

Uninstallation: In order to uninstall Elnec software for programmers, run the uninstallation program, which is accessible by a shortcut in the start menu folder of Elnec, or in the program section of the system control panel. If you also want to remove your configuration settings, you need to delete the configuration file in the application data directory of your user profile. The /SILENT command line switch can be used also here.

Important: The software package for BeeProg3 and BeeHive304 programmers contain also updates of firmware, libraries and operating system for these programmers, which mean (roughly) next 20MB of compressed data. In intent to save download time – and also in intent to save the disk space after installation of software – we come to conclusion to provide two installation packages:

  • the first one: PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) is for all Elnec programmers but doesn’t include BeeProg3/BeeHive304 support.
  • the second one: PG4UWarc3.EXE (and PG4UWarc3-OnDemand.exe) is for all Elnec programmers including BeeProg3/BeeHive304 support. This package is for users of BeeProg3 and BeeHive304 programmers.
Device programmers, list of control software revisions:
Regular versions of control software, significant modifications, list of added devices, device handling improvements and fixed bugs view
OnDemand versions of control software, list of enhancements and bug fixes for other programmers view
OnDemand versions of control software, list of enhancements and bug fixes for BeeProg3/BeeHive304 view

 

Software for device programmers (compatibility: from Windows XP to Windows 10 32-bit and 64-bit):
programmer
(BeeProg3-core programmers)
device list download version last change size (B)
BeeHive304 view | download PG4UWarc3-OnDemand.exe
(OnDemand version)

PG4UWarc3.EXE
(Regular version)

3.23k
(latest SW)

3.23

05.May.2016

07.Apr.2016

79,690,392

79,547,768

BeeProg3   view | download
programmer
(currently produced)
device list download version last change size (B)
BeeHive208S view | download PG4UWarc-OnDemand.exe
(OnDemand version)

PG4UWarc.EXE
(Regular version)

3.23k
(latest SW)

3.23

05.May.2016

07.Apr.2016

55,979,752

55,981,328

BeeHive204   view | download
BeeHive204AP   view | download
BeeHive204AP-AU   view | download
BeeProg2   view | download
BeeProg2AP   view | download
BeeProg2C   view | download
SmartProg2   view | download
MEMprog2   view | download
discontinued programmer
(but still supported)
device list download version last change size (B)
BeeHive8S view | download PG4UWarc-OnDemand.exe
(OnDemand version)

PG4UWarc.EXE
(Regular version)

3.23k
(latest SW)

3.23

05.May.2016

07.Apr.2016

55,979,752

55,981,328

BeeHive4+ view | download
BeeHive4 view | download
BeeProg+ view | download
BeeProg view | download
SEEprog view | download
MEMprog view | download
MEMprogL view | download
JetProg
(DIL48 and ISP modules)
view | download
JetProg
(EPROM/Flash 8ZIF)
view | download
JetProg
(Common multiprogramming module no.1)
view | download
PIKprog2 view | download
PIKprog+ view | download
SmartProg view | download
T51prog2 view | download
T51prog view | download

Notes:

 

  • The support of new devices implemented by OnDemand software is available for BeeProg3/BeeHive304, BeeHive8S/BeeHive208S/BeeHive204/BeeHive4+, BeeProg2/BeeProg2C/BeeProg+ and BeeHive204AP(-AU)/BeeProg2AP programmers only

 

  • The installation file (PG4UWarc.EXE and PG4UWarc-OnDemand.exe) may be keeped to reinstall SW in the future.

 

PC requirements

Minimal PC requirements
Operating system CPU RAM disk space
( free )
USB 2.0
high speed
USB 1.1   LPT LAN
2x BeeHive304 Windows XP C2Quad 2 GB 400 MB 1 Gb
2x BeeHive204AP-AU Windows XP P4 1 GB 400 MB
2x BeeHive204AP Windows XP P4 1 GB 400 MB
2x BeeHive204 Windows XP P4 1 GB 400 MB
BeeHive304 Windows XP C2D 2 GB 400 MB 1 Gb
BeeHive204AP-AU Windows XP P4 1 GB 400 MB
BeeHive204AP Windows XP P4 1 GB 400 MB
BeeHive204 Windows XP P4 1 GB 400 MB
BeeProg3 Windows XP C2D 1 GB 200 MB 100 Mb
BeeProg2 Windows XP P4 512 MB 400 MB
BeeProg2C Windows XP P4 512 MB 400 MB
BeeProg2AP Windows XP P4 512 MB 400 MB
SmartProg2 Windows XP P4 512 MB 400 MB
MEMprog2 Windows XP P4 512 MB 400 MB

Note: For best performance we recommend 1024 x 768 or higher screen resolution.

Recommended PC requirements
Operating system  CPU RAM disk space
( free )
2x USB 2.0
high speed
USB 2.0
high speed
 LAN
2x BeeHive304 Windows 7 Core i5 4 GB 2 GB 1 Gb
2x BeeHive204AP-AU Windows 7 C2Quad 2 GB 2 GB
2x BeeHive204AP Windows 7 C2Quad 2 GB 2 GB
2x BeeHive204 Windows 7 C2Quad 2 GB 2 GB
BeeHive304 Windows 7 Core i3 2 GB 1 GB 1 Gb
BeeHive204AP-AU Windows 7 C2D 1 GB 1 GB
BeeHive204AP Windows 7 C2D 1 GB 1 GB
BeeHive204 Windows 7 C2D 1 GB 1 GB
BeeProg3 Windows 7 Core i3 2 GB 1 GB 1 Gb
BeeProg2 Windows 7 C2D 1 GB 1 GB
BeeProg2C Windows 7 C2D 1 GB 1 GB
BeeProg2AP Windows 7 C2D 1 GB 1 GB
SmartProg2 Windows 7 C2D 512 MB 1 GB
MEMprog2 Windows 7 C2D 512 MB 1 GB

Notes:

  • These PC requirements are valid for 3.14 version of control program for programmers (issued 29/APR/2015) and above.
  • If two programmers are to be connected to a single PC, then we strongly recommend to connect each programmer to separate USB 2.0 High speed controller (USB EHCI). For more information see User manual for the programmer, the “Hardware setup” chapter.
  • Free disk space requirements depends also on used IC device size and number of attached programming sites. For large devices the required free space on disk will be approximately 1000MB + 2x Device size x number of programming sites attached to this PC.
  • Very easy indication, if your PC in hardware/software configuration is good enough for the current software version and current situation with PG4UW/PG4UWMC, is to run Windows task manager (Ctrl+Alt+Del) and see the performance folder. It has to be max. 80% of CPU usage at full run of programming system.

Notes to the BeeHive8S/BeeHive208S programmers:

  • for work with the actual version of SW the BeeHive8S/BeeHive208S programmers must have installed 2GB RAM or above. Some older BeeHive8S come with only 1GB RAM. In this case is RAM size increasing necessary.
    For more information about upgrading of memory for BeeHive8S standalone programmers, visit this link
  • except the above RAM size increase, the PC inside of the all BeeHive8S/BeeHive208S programmer is still above the Minimal PC requirements for actual version of the software.

 

Manuals and other documents

Operating manuals updates
name format language last change size (B)
User manual for BeeHive304 and BeeProg3 programmers PDF english Nov. 07, 2014 6,64 MB
User manual for BeeHive204AP/BeeHive204AP-AU and BeeProg2AP multiprogramming system PDF english May. 22, 2015 9,37 MB
User manual for BeeHive208S Stand-Alone multiprogramming system
(Windows Embedded 8.1 Industry Pro)
PDF english Mar. 04, 2015 4,33 MB
User manual for BeeHive208S Stand-Alone multiprogramming system
(Windows XP Embedded)
PDF english Mar. 04, 2015 3,14 MB
User manual for BeeHive8S Stand-Alone multiprogramming system PDF english Mar. 18, 2009 1,10 MB
Latest version of User manual for BeeHive204, BeeProg2, BeeProg2C, SmartProg2 and MEMprog2 device programmers PDF english May 22, 2015 6,95 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: BeeHive204, BeeProg2, BeeProg2C, BeeProg+, SmartProg2, MEMprog2, SEEprog)
PDF english June. 26, 2012 5,29 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: BeeHive204, BeeHive4+, BeeProg2, BeeProg+, SmartProg2, MEMprog2, T51prog2, PIKprog2, MEMprogL, SEEprog)
PDF english Apr. 13, 2011 5,43 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: JetProg, BeeProg, LabProg+, SmartProg2, SmartProg, PREPROM-02aLV, MEMprog, MEMprogL, T51prog, 51&AVRprog, PIKprog+, PIKprog, SEEprog)
PDF english Aug. 17, 2005 3,71 MB
User manual for BeeHive4 multiprogramming system PDF english Sep. 16, 2005 1,53 MB
User manual for all Elnec device programmers PDF deutsch Feb. 02, 2004 3,05 MB
User manual for JetProg – multiprogramming system PDF english Feb. 25, 2003 405,88 KB
User manual for Elnec EPROM simulators PDF english Aug. 01, 2003 1,06 MB
User manual for EREPROM-01A eraser PDF english Sep. 22, 2003 47,24 KB

You need to have PDF files. You can use Adobe Acrobat Reader. Get Acrobat Reader
But better might be Foxit (PDF) Reader – faster and smaller. Get Foxit Reader

 

Unsupported products

Last version of software for no longer supported products:
product OS download version last change size (B)
LabProg+ (device list) Windows pg4uwarc321.exe 3.21 Jan. 28, 2016 53,3 MB
PREPROM-02aLV (device list) Windows pg4uwarc315.exe 3.15 Jun. 30, 2015 51,9 MB
51&AVRprog (device list) Windows pg4uwarc299.exe 2.99 Jun. 20, 2013 42,8 MB
PIKprog (device list) Windows pg4uwarc299.exe 2.99 Jun. 20, 2013 42,8 MB
LabProg-48LV (device list) Windows pg4uwarc274.exe 2.74 Dec. 16, 2010 31,60 MB
PREPROM-02 (device list) Windows pg4uwarc251.exe 2.51 Aug. 14, 2008 24,07 MB
PREPROM-03 EPROM/Flash gang programmer (device list) PG023ARC.EXE 3.98c Aug. 16, 1999 295,28 KB
PREPROM-01 EPROM programmer PGO1.ZIP 12/1999 138,05 KB
SIM2051 emulator/programmer AT89C2051 S2051ARC.EXE 3.11 Mar. 21, 2000 197,57 KB
T-EMU52 emulator TEMU52AR.EXE 1.44 Jan. 03, 2002 245,26 KB
SIMEPROM-01B/-02/-02aLV
simulators
simwarc.exe 1.18 22.May.2007 1,41 MB
SIMEPROM-01B/-02/-02aLV
simulators
sim12arc.exe 4.17 28.May.2002 256,11 KB
SIMEPROM-01/-01A EPROM simulators SIM12ARC.EXE 6/2001 256,11 KB

 

Software for device programmers (DOS)
programmer download version last change size (B)
JetProg, LabProg+, LabProg-48LV, SmartProg, T51prog, 51&AVprog, PIKprog+, PIKprog, SEEprog, PREPROM-02 PG4Uarc.EXE 4.93a 26.Jun.2003 2,46 MB

Note: