Various Instruments -

ELECTRICAL TEST Kit

1027 TK

1027 TK is an electrical technician’s kit which provides the electrical testing needs for installation, plant maintenance and repair of electrical systems.

Kit includes:
● 189 DM autoranging digital multimeter with 11
functions including AC/DC voltage, Capacitance,
Frequency, Resistance, AC/DC current…..etc.● 888 PMR phase rotation and motor rotation tester.

● LVD-15 non-contact voltage detector
(50 ~1000 Vac) + flashlight.● High quality carry case.

ELECTRICAL TEST Kit

1021 TK(2950 CL + ALS-2)

FEATURES

2950 CL

● Pocket size.
● 4000 counts.
● Full automatic measurement :

Voltage measurement.
Current measurement.
Resistor measurement.
● Data hold function.
● Continuity check.
● Diode measurement.
● Select function.
● Low battery indication.
● Auto off function.
● Flashlight (auto off in 1 minute).

ALS-2

● Use with any clamp meter.
● x10 mode allows for more accurate measurements of low amperage devices.
● x1 mode allows for direct reading.
● 4mm voltmeter input jacks.
● Integrated ground conductor.
● 10 amp capacity.
● 10cm plug cord for greater flexibility.

Millimhm Meter

4136 mO

FEATURES

● Microprocessor-controlled.
● Four terminal measurement.
● Measures down to 100μΩ.
● 5 Ranges from 200.0mΩ to 2000Ω.
● Maximum resolution of 100μΩ.
● Three test currents with over-temperature protection.
● Protection against inadvertent connection to over voltage.
● Large LCD.
● Potential lead resistance and current lead resistance checks.
● “Full-featured” EnerSave

inside.
● EnerSave

Auto hold.
● EnerSave

Auto off.
● Lightweight, robust & compact.
● Indicators show if reading may be invalid (RP, RC, and
temperature).
● “O-Ring” sealed case.

Millimhm Meter

4137 mO

FEATURES

inside.
● EnerSave

Auto hold.
● EnerSave

Auto off.
● Lightweight, robust & compact.
● Indicators show if reading may be invalid (RP, RC, and
temperature).
● “O-Ring” sealed case.

Low Resistance Ohm Meter

6237 DLRO

FEATURES

● Microprocessor-controlled.
● Measure down to 1μΩ.
● 6 ranges from 2.000mΩ to 200.0Ω.
● Maximum resolution of 1μΩ.
● Three test currents with over-temperature protection.
● Four terminal measurement.
● Protection against inadvertent connection to over-
voltage. (crow bars for current and voltage)
● Clear & large LCD.
● Potential lead resistance and current lead resistance checks.
● “Full-featured” EnerSave™ Inside.
● EnerSave™ Auto-hold.
● EnerSave™ Auto-off.
● Rechargeable battery operated
● Robust & compact.
● Indicators show if reading may be invalid (RP, RC, and
temperature).
● “O-Ring” sealed case.

AC & DC Analog Leakage Meters

506 EL

FEATURES

● High quality movement.
● Compact and lightweight; easy to use and store.
● Mirror scale: for easier viewing & reading.
● Built-in stand makes reading and measuring easy.
● 200μA full scale value.
● Fuse-protected.
● Low battery indication.

AC & DC Analog Leakage Meters

507 EL

FEATURES

AC & DC Analog Leakage Meters

2108 EL

FEATURES

● High quality Taut Band movement.
● Four functions : DC current, AC current, AC+DC current, and ACV
measurement.
● Three input resistance ranges: 1kΩ,1.5kΩ and 2kΩ.
● 200uA full scale value.
● ±2.5% full scale value accuracy.
● Built-in overload protection circuit.
● Robust, compact and easy to carry.

AC & DC Analog Leakage Meters

1807 TB

FEATURES

● AC Voltage Input/output range：
100~240 Vac
● Frequency：
50~60Hz
● Current：
10A

Low Voltage Detector

LVD-15

FEATURES

● Bright LED and audible alarm sound when voltage is present.
● Designed for non-contact voltage detection.
● Can be used to find a break in a wire.
● Flashlight function.
● ON/OFF switch for longer battery life.

Low Voltage Detector

LVD-17

FEATURES

● Microprocessor-controlled smart voltage detector.
● Bright LED and audible alarm sound when voltage is present.
● Designed for non-contact voltage detection.
● Sensitivity adjustable with thumbwheel.
● Adjustable for use on power wiring plus lighting, thermostats and
other low voltage circuits.
● LED indication for battery condition.
● Identify Hot and Neutral.

OverHead Lines Contact Voltage & Low Voltage Indicator

LVD-415

FEATURES

● No batteries required.
● Every circuit is doubled.
● Buzzer indicates voltage detected.
● Led indicates voltage detected.
● Neon scale indicates voltage.
● Dual HBC fuses.
● High grade fiber glass probes.
● Super polished fiber glass.
● High strength connecting cord.
● Heavy duty rated.
● Replaceable tips.
● Choice of tips available.
● Lightweight.
● Small storage space.
● Strong strength reliefs.
● Double poles non-polarized.
● Suitable for 45 to 70 Hz networks.
● Contact detector type.
● Passive circuitry.
● Fiber glass 1.6mm – CU 35um PCB.
● Super bright neon lights and LEDs.
● Ergonomically-designed.
● EN 61010-031 CAT IV 500V.

Voltage/Continuity Tester

VOT-52

FEATURES

● Voltage test: 12V to 1000V AC/DC
(8 LEDs) with indication by buzzer.
● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.
● Test leads positioned at 19mm apart.

● Interchangeable probe tip for 2mm and 4mm.
● Polarity test : LED +/-
● Audible continuity test.
● Phase rotation test : /
● Self-test button to ensure proper function of the device prior to testing.
● Waterproof design, protection class: IP65.
● Phase / Neutral identification.
● Rubberized double-molded housing.
● ELCB / RCD trip test.
● Flashlight function.
● Safety standard :
IEC/EN 61010-1 III 1000V

IEC/EN 61010-1 IV 600V
IEC/EN 61243-3
EN 61326-1

Voltage/Continuity Tester

VOT-50

FEATURES

● Voltage test: 12V to 690V AC/DC (7 LEDs) with indication by
buzzer.
● Voltage range: 12V, 24V, 50V, 127V, 230V, 400V, 690V.
● Polarity test: LED +/-
● Audible continuity test
● Self-test button to ensure proper function of the device prior to
testing.
● Waterproof design, protection class: IP54
● Phase / Neutral identification
● Integrated storage clips for test probe.
● Rubberized injection molding.

Voltage/Continuity Tester

VOT-51

FEATURES

Voltage/Continuity Tester

CT-01

FEATURES

● Audible and optic continuity test.
● Audible and optic voltage check.
● Voltage protection : 600V
● Robust and ergonomic housing.
● For checking electric light bulbs, securings, wirings and so on.
● Application : resistor, voltage, semiconductor, capacitor and so on.

Loop Calibrator

6500 LC

FEATURES

● 4-20mA (1kΩ load, 24V Loop Supply).
● 0.025% Basic Accuracy.
● Simple Operation Interface.
● Auto Ramp and Step Functions.
● 0-20mA, 0-24mA selectable.
● Incremental percentage setting : 0-100%.
● Warning beeper when output is open.
● 0-24V output.
● The minimum load of 20kΩ on voltage mode.

Sound Level Meter

2310 SL

FEATURES

● Max. & Min. function.
● Over & under range indication.
● 4-digit LCD with bar graph.
● Frequency weighting characteristic for 2 times per second.
● AC signal output.
● Low battery indication.

Circuit Breaker Identifiers

188 FFF

FEATURES

● The 188FFF is a Fuse and Fault Finder which comprises of two
parts : The Receiver and the Transmitter.
● The Transmitter, draws a current from the mains supply circuit to
which it is connected to. The Signal
● Current from the Tx is at about 10kHz. The Transmitter is powered
by the mains and requires no batteries.
● The 10kHz signal current generated by the Transmitter is then
searched(sniffed) by the Receiver to detect the Fuse, Circuit
Breaker or the faulty circuit.
● The Receiver is a tuned circuit which has it’s center frequency tuned
to about 10kHz. The sensor is located in the tip of the Receiver.
● The amplitude of the received signal is shown on a bar-graph type
Leds.
● The more Leds ON, the stronger the signal.
● The Receiver uses one 9V battery.

Circuit Breaker Identifiers

190 CBI

FEATURES

● 190 CBI is an easy tool to find the circuit breaker or fuse supplying
electrical power to an outlet or lighting fixture. Just plug the
transmitter into the outlet.
● Use the receiver to scan the circuit breaker panel box. An audible
tone will be clearly heard when the right circuit breaker is scanned.
● The plug of transmitter is changeable. The plug of transmitter could
be changed for customers’ requirement from different countries.

Circuit Breaker Identifiers

191 CBI

FEATURES

● 191 CBI is an easy tool to find the circuit breaker or fuse supplying
electrical power to an outlet or lighting fixture. Just plug the
transmitter into the outlet.
● Use the receiver to scan the circuit breaker panel box. An audible
tone will be clearly heard when the right circuit breaker is scanned.
● The plug of transmitter is changeable. The plug of transmitter could
be changed for customers’ requirement from different countries.

Power Meter

8015 PM

FEATURES

● Determine the running cost of your appliances.
● Measure voltage, current, frequency, watt, power factor, and greenhouse
gas emissions.
● Optical USB to RS-232 data transmission.
● 2 Optical LEDs are built-in for data transfer.
● Transferring and showing real-time data to a PC.
● Make informed decisions when purchasing appliances and equipment.
● Reduce your electricity bill.
● Calculate electrical expenses by real, hour, month.
● Can make different kinds of plugs for different countries / areas,

such as Type B, E, G, I plugs…..etc.
● Data communication function.
● Freely set upper and lower limit for V,A,W and

alarm when measured value is out of limit.
● Backlight function.

Power Meter

PM-10,PM-15

FEATURES

● Determine the running cost your appliances.
● Make informed decisions when purchasing appliances and
equipment.
● Reduce your electricity bill.
● Measure Voltage, Current, Power, Volts, Amps, Power Factor, and
Greenhouse Gas Emissions.
● Calculate electrical expenses by day, week, month, and even an
entire year.

Audio Impedance Testers

1106 IM

FEATURES

● Large LCD : 68 × 34mm (2.677″ × 1.338″).
● True measurement of speaker systems actural impedance at 1kHz.
● Three test ranges allow testing of home theater and commercial
sound systems.
● Measures transformer impedances.
● Battery operation.
● Low battery indication.
● Data hold function.
● 0Ω adjustment.

Audio Impedance Testers

1107 IM

FEATURES

● Large LCD : 68 × 34mm(2.677″ × 1.338″).
● True measurement of speaker systems actural impedance at 1kHz.
● Three test ranges allow testing of home theater and commercial
sound systems.
● Measures transformer impedances.
● Battery operation.
● Low battery indication.
● Data hold function.
● 0Ω adjustment.

Audio Impedance Testers

1506 IM

FEATURES

● High quality Taut Band movement.
● Battery operated.
● Timer function for hands free use.
● Battery indicator.
● The tester measure with a frequency of 1kHz.
● Measure speaker’s impedance.
● Measure speaker lines (connected to load).
● Help to calculate and check audio power systems.
● Ideal for public address installation and maintenance.
● Measure transformer impedances.

Audio Impedance Testers

2706 IM

FEATURES

● True measurement of speaker systems actual impedance at 1kHz.
● Three test ranges (20Ω / 200Ω / 2000Ω) allow testing of home
theater and commercial sound systems.
● Measures transformer impedances.
● Battery operated.
● Low battery indication.
● Data hold function.
● Timer function for continuous hands free operation.
● The timer can last about 3-5 minutes when users press.
● TEST ON/OFF button.

AC Line Separators

ALS-1

FEATURES

● x10 Model allows for more accurate
measurements of low amperage devices.
● Direct reading x1 mode.
● 4mm Voltmeter input jacks.
● Intergrated ground conductor.
● 10 amp capacity.

AC Line Separators

ALS-2

FEATURES

● x10 Model allows for more accurate
measurements of low amperage devices.
● Direct reading x1 mode.
● 4mm Voltmeter input jacks.
● Intergrated ground conductor.
● 10 amp capacity.
● 10cm plug cord for greater flexibility.

Battery Tester

6470 BT

FEATURES

● 2000 counts.
● DC Voltage measurement.
● 4-wire resistance measurement.
● Data hold function.
● Low battery indication.
● 9V DC power supply.
● Measure battery types: Li-ion, Ni-Cd, Ni-MH
● Simple operation.
● Lead resistance and contact resistance eliminated.

Resistor Calibration Boxes

RCB-1

FEATURES

● The RCB-1 is used to verify and proof any High Voltage Insulation
Testers. It can be utilized to calibrate all High Voltage Insulation
Testers very accurately Analogs or Digitals.
● Some institutions and large industries requested their own calibrator
too, therefore, SEW started manufacturing the RCB for special
customers.

Resistor Calibration Boxes

RCB-3

FEATURES

● The RCB-3 is used to verify and proof any High Voltage Insulation
Testers. It can be utilized to calibrate all High Voltage Insulation
Testers very accurately Analogs or Digitals.
● Some institutions and large industries requested their own calibrator
too, therefore, SEW started manufacturing the RCB for special
customers.

Resistor Calibration Boxes

RCB-3-1T(A)

FEATURES

● The RCB-3-1T is used to verify and proof any High Voltage
Insulation Testers. It can be utilized to calibrate all High Voltage
Insulation Testers very accurately Analogs or Digitals.
● Some institutions and large industries requested their own calibrator
too, therefore, SEW started manufacturing the RCB for special
customers.

Resistor Calibration Boxes

RCB-3-1T(B)

FEATURES

Resistor Calibration Boxes

ITC 8

FEATURES

● The ITC 8 can be utilized to check calibration of resistance ranges
of insulation testers and multimeters.
● The resistance checker box is also used to verify insulation testers
and multimeters.

Mini Appliance Checker

880 AT

FEATURES

● The 880 AT is a simplified Version of an appliance tester which use
low voltage and low current to perform it’s checks.
● Application Example
The appliance is plugged into the mini appliance checker, then the
probe make contact with the protective conductor.
● Other appliance checking
Washing Machine Toaster Iron Dish Washer
Stove

AC Voltage Proving Units

HLV-1

FEATURES

● Designed to proof.
AC voltage detectors
AC voltage testers
● Compact, handheld, and easy to carry and use.
● Battery operated.
● LED indicates when power is “ON”.
● Normal 4mm test leads.

AC Voltage Proving Units

HLV-2

FEATURES

AC Voltage Proving Units

HLV-3

FEATURES

TEST BOX

6280 TB

FEATURES

● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.
● For checking AC voltage.
● For checking a RCD tester’s test current & time in mA(ms).
● For checking a loop tester.
● For wiring check (Phase, Neutral, Earth).
● For checking continuity.
● For checking insulation (The maximum is 1.2kV).
● For checking UK16th edition.

GFCI Socket Tester

TEL5